|
Post by dacjeep on May 30, 2011 19:46:50 GMT -5
Rotated the tires Cleaned the sand and crap out of the emergency break shoes Cleaned the engine compartment Checked underneath for loose anything inspected all the U joints Cleaned and re-wrapped winch cable
|
|
|
Post by HamiltonLJ on May 31, 2011 18:47:08 GMT -5
I washed mine also! A little nanowax on the frame she's as good as new!
|
|
|
Post by waterman on Jun 1, 2011 8:12:09 GMT -5
I washed and waxed it over the weekend,cleaned the spider webs out of it,, went for a ride ;D and used up the stale gas that was in the tank from last year
|
|
|
Post by Lyon on Jun 1, 2011 14:11:23 GMT -5
Never thought I'd see the day Tom used Nanowax. LOL!!!
So here is my new list. Installed AC compressor again because the replacement was bad. Did a dual AC electric fan mod inplace of the old fan set up. Did the SYE and removed the TC drop. Shimmed the rear axle 4 degrees. Finally got the rear put together and installed. Installed the Aussie and test drove it. Has a whining noise. Drove it for a few days and pulled it apart and changed one pinion bearing. Once again no luck. Still noisy. d**n used axles. Might be off to York tomorrow to pick up another rear. Replaced all 3 U-joints in the front drive shaft. Thank you to Dennis for putting in all the long hours, hard work and sweat to get this all done. Tested it out a little on the trails for a short time and got my first small dent. (Which obviously is fixed already. Filled it with Nanawax. hahaha!!!!) Today just cleaned the interior. :-)
|
|
|
Post by HamiltonLJ on Jun 1, 2011 18:40:09 GMT -5
Waterman washed his and waxed it Well the nanowax is in the carwash.
|
|
chuck
Mud Slinger
Posts: 181
|
Post by chuck on Jun 2, 2011 2:35:41 GMT -5
As usual, not much. Fortunatly the last coat of wax was when I picked it up from the dealer in Sept 1999. One of these days I will break down and apply some wax. The week before we went to Rausch Creek last month, I had a new battery installed as it was getting weak. I have been working on installing a rack for my CB, GPS and eventually scanner. It is coming along, now need to work on some wiring. Have some other jobs to work on as well, but this old man is too slow. Take care guys.
|
|
|
Post by muddin310 on Jun 2, 2011 6:35:55 GMT -5
jacked the front of the jeep . took off the front big shackels and drop bowed springs waiting for the new shackels the come in ..
|
|
|
Post by rredneck on Jun 5, 2011 7:36:36 GMT -5
ciean & waxed jeep repainting frame today
|
|
|
Post by Lyon on Jun 22, 2011 17:14:29 GMT -5
|
|
|
Post by HamiltonLJ on Jun 22, 2011 18:47:20 GMT -5
I see someone doesn't clean under their flares!
What did you do to your tire last night?
|
|
|
Post by Lyon on Jun 22, 2011 20:41:29 GMT -5
Well, 3 flairs are clean underneath now. Nobody sees under there anyway. haha! But just for you Tom, I did clean underneath while I was working on it. Came out this morning to this Not sure what hit it but it was enough to kill the tire
|
|
|
Post by HamiltonLJ on Jun 23, 2011 16:49:50 GMT -5
Well that sucks!
|
|
|
Post by Lyon on Jul 10, 2011 14:05:14 GMT -5
And another list emmerges... New battery and ends, adjustable upper control arms and transmission cooler. :-)
|
|
|
Post by HamiltonLJ on Jul 10, 2011 15:56:23 GMT -5
I drove mine today! Does that count if you drive it every day.
|
|
chuck
Mud Slinger
Posts: 181
|
Post by chuck on Jul 10, 2011 16:57:05 GMT -5
Mickey dangling from the roll bar at 70 mpg on Rt 295, quite a sight.
|
|