|
Post by waterman on Jan 7, 2009 12:09:48 GMT -5
Ok heres the thing,,i have something going on and i cant find it,,,what happens is when im going down the road be slow or fast,,,when i shift gears it feel like that ass end is moving to one side. I jack this thing up all the springs look good no signs of a broken spring,,,all spring bushings look good no bent shackels,,spring perches all look good,,,and theres no signs of things moving anywhere. Rear is a currie 9" locked 4:88. Ive replaced all motor mounts trans mount,,,,It feels like a boken mount but i cant find it
|
|
|
Post by mucksavage on Jan 7, 2009 12:34:42 GMT -5
I had this happen & in my case, a u-bolt was cracked. I couldn't see it, and would've never found it until & spent hours under it with wrenches.
Maybe your locker's acting up? (locking & un-locking?)
|
|
|
Post by waterman on Jan 7, 2009 13:20:06 GMT -5
Na dont think its the locker,,,only cause that feels way different when that does happen
|
|
|
Post by blackrubi on Jan 7, 2009 13:21:48 GMT -5
you were next to that yellow jeep yesterday, did you check you lug nuts ;D
Any chance you snapped an axle shaft and it is only working on one side?
|
|
|
Post by waterman on Jan 7, 2009 14:05:23 GMT -5
Na this has been going on now for a month or so,,but i did think of that brad!!
|
|
|
Post by blackrubi on Jan 7, 2009 14:41:11 GMT -5
motor mount?
|
|
|
Post by waterman on Jan 7, 2009 14:47:41 GMT -5
Changed all mounts
|
|
|
Post by mucksavage on Jan 7, 2009 15:09:16 GMT -5
A long shot maybe, but a spring-eye bolt?
|
|
|
Post by waterman on Jan 7, 2009 15:25:36 GMT -5
Put the air gun to them and there tight and none of them are broke
|
|
|
Post by blackrubi on Jan 7, 2009 15:44:32 GMT -5
any chance it is a result of low tire pressure since you tend to trailer and not inflate for driving?
|
|
|
Post by mudboy on Jan 7, 2009 15:52:59 GMT -5
Put the air gun to them and there tight and none of them are broke when tighten u bolts the will never be tightened properly by a impact. U-bolts are made out of spring steel and stretch. the only way to properly tighten you bolts is by hand tools.
|
|
|
Post by mudboy on Jan 7, 2009 15:54:44 GMT -5
after re reading everything I realized you were probably talking about the alignment pins. how are your shocks/bushings?spring perches arent rounded off? body mounts?
|
|
|
Post by waterman on Jan 7, 2009 16:12:38 GMT -5
Tire pressure was check that was good,,,i do drive it around town so it doesent feel left out,,,U bolts aways get tighten by hand and rechecked from time to time,,,just run in by air guy,,,shocks arent gooing to make it do what its doing,,,,spring preches are all good ,,,same as body mounts
|
|
|
Post by mucksavage on Jan 7, 2009 16:22:07 GMT -5
Loose nut behind the wheel? (Sorry, I couldn't resist throwing in a bad joke)
|
|
|
Post by waterman on Jan 7, 2009 16:54:35 GMT -5
OOOOHHHH thats way loose at times!!!
|
|